OPE-QI Series
2016년 October 26일
0 
OPE-QI Series
Linear Programmable DC Power Supply
Economical type, 4 Channels (2 variable output, 2 fixed output)
OPE-QI Series is high performance programmable DC power supply with RS232C or RS485 interface based on SCPI (Standard Commands for Programmable Instruments) protocol and the combination of bench-top and system features in these power supplies provides versatile solutions for your design and test requirements in the industrial fields, R&D institute center and education fields.
Dimension
19inch half x 2U size : 213mm(W) x 88mm(H) x 362mm(D)
| 1 | LCD (Volt/Curr Message Display module) | 13 | Fixed 1 Over Load Protection Lamp |
| 2 | Encoder S/W for changing Volt/Curr | 14 | Fixed 2 Over Load Protection Lamp |
| 3 | I/O or LOCAL Key | 15 | Fixed 1 & Fixed 2 Voltage selection switch |
| 4 | Ouput ON/OFF Key | 16 | Fixed 1(5V/2A & 3.3V/2A) + output terminal |
| 5 | Volt/Curr select or Limit Display Key | 17 | Fixed 1(5V/2A & 3.3V/2A) – ouput terminal |
| 6 | OUTPUT channel SELECT or Tracking Key | 18 | Fixed 2(15V/1A & 12V/1A) + ouput terminal |
| 7 | Volt/Curr Cursor or menu change Key | 19 | Fixed 2(15V/1A & 12V/1A) – ouput terminal |
| 8 | Volt/Curr Cursor or menu change Key | 20 | P1 Output Terminal (Positive Output) |
| 9 | P1 Constant Current mode indicate Lamp | 21 | P1 Output Terminal (Negative Output) |
| 10 | P2 Constant Current mode indicate Lamp | 22 | P2 Output Terminal (Positive Output) |
| 11 | P1,P2 channel Tracking mode indicate Lamp | 23 | P2 Output Terminal (Negative Output) |
| 12 | Remote Interface mode indicate Lamp | 24 | Main Power ON/OFF Switch |
- Two isolated variable output provided
- Fixed output that enables the selection of 5 V/ 2 A & 3.3 V/ 2 A is provided
- Fixed output that enables the selection of 15 V/ 1 A & 12 V/ 1 A is provided
- OUTPUT ON/OFF function provided
- Tracking Mode (two outputs controlled at the same time) provided
- Save and Recall up to five(5) operation states (Voltage, Current)
- 19”Half x 2U slim size (less than 300 W)
- RS-232C standard (RS-485 Option)
TRACKING MODE
Two channels can be controlled at once.
If single channel power supply was supplied for each producer when it comes to your company’s mass production system, replace it with the power supply in two channels that supports our company’s tracking mode!
There is no need to set up two channels’ voltage and current which is cumbersome.
Instead, pressing simply one button, the tracking mode button can set up two channels in the same way using only one setting for the voltage, current and all the functions.
STORE & RECALL
Save and Recall Voltage and Current set by user easily
OPE Series can store and recall the voltage and current set by user.
Even when a user is not an engineer, the user can use it easily for the production, product inspection, reliability test etc., with the Store and Recall function that set up and stored in advance.
Line-Up and Specification
| Model Parameter |
OPE-185QI |
OPE-303QI |
OPE-305QI |
OPE-503QI |
|---|---|---|---|---|
| Output rating |
0~18V, 0~5A 2CH |
0~30V, 0~3A 2CH |
0~30V, 0~5A 2CH |
0~50V, 0~3A 2CH |
|
Resolution |
||||
|
Programming/Readback |
≤ 6mV / ≤ 1.5mA |
≤ 7.5mV / ≤ 1mA |
≤ 7.5mV / ≤ 1.5mA |
≤ 15mV / ≤ 1mA |
|
Display Meter |
100mV / 10mA |
100mV / 10mA |
100mV / 10mA |
100mV / 10mA |
|
Programming Accuracy (@25℃ ±5℃)±(%of output + offset) |
||||
|
Voltage |
0.2% + 120mV |
0.2% + 200mV |
0.2% + 200mV |
0.2% + 300mV |
|
Current |
0.2% + 25mA |
0.2% + 15mA |
0.2% + 25mA |
0.2% + 15mA |
|
Read-back Accuracy (@25℃ ±5℃)±(%of output + offset) |
||||
|
Voltage |
0.2% + 120mV |
0.2% + 200mV |
0.2% + 200mV |
0.2% + 300mV |
|
Current |
0.2% + 25mA |
0.2% + 15mA |
0.2% + 25mA |
0.2% + 15mA |
|
Ripple & Noise |
≤ 2mVp-p, ≤ 2mArms |
≤ 2mVp-p, ≤ 2mArms |
≤ 2mVp-p, ≤ 2mArms |
≤ 3mVp-p, ≤ 2mArms |
|
Voltage Programming Speed(No load) |
||||
|
Rising time |
≤ 40㎳ |
≤ 40㎳ |
≤ 40㎳ |
≤ 70㎳ |
|
Falling time |
≤1.2s |
≤1.2s |
≤1.2s |
≤1.5s |
| Model Parameter |
OPE-801QI |
OPE-1001QI |
OPE-1201QI |
|---|---|---|---|
| Output rating |
0~±80V, 0~2A 2CH |
0~±100V, 0~1A 2CH |
0~±120V, 0~1A 2CH |
|
Resolution |
|||
|
Programming/Readback |
≤ 30mV / ≤ 0.8mA |
≤ 40mV / ≤ 0.5mA |
≤ 50mV / ≤ 0.5mA |
|
Display Meter |
100mV / 10mA |
1V / 10mA |
1V / 10mA |
|
Programming Accuracy (@25℃ ±5℃)±(%of output + offset) |
|||
|
Voltage |
0.3% + 500mV |
0.5% + 800mV |
0.5% + 900mV |
|
Current |
0.2% + 15mA |
0.2% + 15mA |
0.2% + 15mA |
|
Read-back Accuracy (@25℃ ±5℃)±(%of output + offset) |
|||
|
Voltage |
0.3% + 500mV |
0.5% + 800mV |
0.5% + 900mV |
|
Current |
0.2% + 15mA |
0.2% + 15mA |
0.2% + 15mA |
|
Ripple & Noise |
≤ 6mVp-p, ≤ 2mArms |
≤ 0.01%mVrms, ≤ 2mArms |
≤ 0.01%mVrms, ≤ 2mArms |
|
Voltage Programming Speed(No load) |
|||
|
Rising time |
≤ 70㎳ |
≤ 70㎳ |
≤ 70㎳ |
|
Falling time |
≤1.5s |
≤1.5s |
≤1.5s |
| Common Details | 2Fixed output channels(5V or 3.3V& 2A / 15V or 12V & 1A) Half of 19inch x 2U size: 213mm(W) x 88mm(H) x 362mm(D), RS-232C interface |
||
Accessories
– Operating Manual 1pc
– Window Application Demo Program (CD)
– AC input cord 1pc (1.8meter)
– DC output cable 2pc
Options
– RS485 Module
– RS485 to RS232 Convertor
– RS232C Cross Cable 1M, 2M, 4M, 10M
– 100V, 110V, 115V, 230V ± 10%, 50~60Hz AC Power input and 3Phase
– Rear Output Terminal
– Rack Mount Support (Bracket and shelf)
